Using coupled micropillar compression and micro-Laue diffraction to investigate deformation mechanisms in a complex metallic alloy Al13Co4

In this investigation, we have used in-situ micro-Laue diffraction combined with micropillar compression of focused ion beam milled Al13Co4 complex metallic alloy to study the evolution of deformation in Al13Co4. Streaking of the Laue spots showed that the onset of plastic flow occured at stresses as low as 0.8 GPa, although macroscopic yield only becomes apparent at 2 GPa. The measured misorientations, obtained from peak splitting, enabled the geometrically necessary dislocation density to be estimated as 1.1 x 1013 m-2

Hierarchical modelling of in situ elastic deformation of human enamel based on photoelastic and diffraction analysis of stresses and strains

Human enamel is a typical hierarchical mineralized tissue with a two-level composite structure. To date, few studies have focused on how the mechanical behaviour of this tissue is affected by both the rod orientation at the microscale and the preferred orientation of mineral crystallites at the nanoscale. In this study, wide-angle X-ray scattering was used to determine the internal lattice strain response of human enamel samples (with differing rod directions) as a function of in situ uniaxial compressive loading. Quantitative stress distribution evaluation in the birefringent mounting epoxy was performed in parallel using photoelastic techniques. The resulting experimental data was analysed using an advanced multiscale Eshelby inclusion model that takes into account the two-level hierarchical structure of human enamel, and reflects the differing rod directions and orientation distributions of hydroxyapatite crystals. The achieved satisfactory agreement between the model and the experimental data, in terms of the values of multidirectional strain components under the action of differently orientated loads, suggests that the multiscale approach captures reasonably successfully the structure-property relationship between the hierarchical architecture of human enamel and its response to the applied forces. This novel and systematic approach can be used to improve the interpretation of the mechanical properties of enamel, as well as of the textured hierarchical biomaterials in general

Carbon fibre lattice strain mapping via microfocus synchrotron X-ray diffraction of a reinforced composite

Synchrotron X-ray diffraction (SXRD) strain analysis is well established for high crystalline materials such as metals and ceramics, however, previously it has not been used in Carbon Fibre Reinforced Polymer (CFRP) composites due to their complex turbostratic atomic structure. This paper will present the feasibility of using SXRD for fibre orientation and lattice strain mapping inside CFRPs. In particular, it is the first time that the radial {002} and axial {100} strains of carbon fibre crystal planes have been analysed and cross-validated via numerical multi-scale simulation in a two-scale manner. In order to simplify the analysis and provide comparable estimates, an UniDirectional (UD) CFRP formed into a well-established humpback bridge shape was used. The lattice strain estimates obtained from SXRD showed localised stress concentrations and effectively matched the numerical results obtained by modelling. The mean absolute percentage differences between the two were 25.8% and 28.5% in the radial and axial directions, respectively. Differences between the two measurements are believed to originate from the non-uniform thermal history, forming geometry and tool-part interaction which leads to localised residual strains in the laminate which are unable to be fully captured by the numerical simulation performed. The carbon fibre microstructures of the inner plies adjacent to the tool were found to be significantly influenced by these factors and therefore the largest errors were observed at these locations. The approach presented has significant promise and implications for research into the micromechanics of composite materials and areas for future improvement have been outlined

Observation of dose-rate dependence in a Fricke dosimeter irradiated at low dose rates with monoenergetic X-rays

<p>Absolute measurements of the radiolytic yield of Fe3+ in a ferrous sulphate dosimeter formulation (6 mM Fe2+), with a 20 keV x-ray monoenergetic beam, are reported. Dose-rate suppression of the radiolytic yield was observed at dose rates lower than and different in nature to those previously reported with x-rays. We present evidence that this effect is most likely to be due to recombination of free radicals radiolytically produced from water. The method used to make these measurements is also new and it provides radiolytic yields which are directly traceable to the SI standards system. The data presented provides new and exacting tests of radiation chemistry codes.</p

A study of phase transformation at the surface of a zirconia ceramic

Yttria Partially Stabilized Zirconia (YPSZ) is one of the most important engineering ceramic materials in that it displays a whole host of outstanding structural and functional properties. Of particular importance for load-bearing applications is the remarkable fracture toughness of YPSZ that arises from its ability to undergo martensitic transformation, a phase transformation that is dependent on stress, temperature, time, humidity, grain size, and the proximity of an interface. The present study was aimed at revealing the influence of the thermal ageing on the tetragonal to monoclinic phase transformation in the near-surface regions of YPSZ. In order to perform qualitative and quantitative characterisation of the phase composition, three principal microscopic techniques were employed: atomic force microscopy, depth resolved Raman micro-spectroscopy, and synchrotron X-ray diffraction. Satisfactory consistency was achieved between the results obtained using different techniques. Moreover, the data obtained in this way displayed complementarity that provided valuable input for the development of thermodynamic modelling of the complex inter-dependence between phase state and processing history of zirconia ceramics